AUTONET TV

Positive Crankcase Ventilation ? PCV Valve Service at Muffler & Go

Hello Fenton! Did you know that the first federally-mandated emissions control device was introduced in the 1960's? The Positive Crankcase Ventilation valve, or PCV valve, has been installed in MI vehicles since 1964 and represents the first legislation by the United States government to regulate harmful emissions as well as to improve performance in the country's vehicles.

The PCV valve, as you can probably guess, is located on the crankcase. The crankcase is the lowest part of a vehicle's engine. It houses the crankshaft and the engine oil. The crankshaft connects to the pistons that power the engine.

Pistons are pushed down when fuel is burned in an engine. This causes the crankshaft to rotate, which sends power to the transmission.  It ultimately turns the axles and causes the vehicle to move. Some of the gases released by the burning fuel squeeze around the pistons and down into the crankcase.

If the escaped gases mix with the engine oil in the crankcase, oil sludge develops. This sludge has the consistency of petroleum jelly and can cause damage by clogging up passageways in the engine. Further, escaped gases can build up pressure inside the crankcase that can blow out seals and gaskets.

Before 1964, a hose was attached to the crankcase that vented escaped gases out into the air. These gases contained about 70% unburned fuel as well as harmful emissions. The PCV valve was designed to curb these harmful emissions as well as recapture unburned fuel.

The PCV valve is a small, one-way valve that allows escaped gases to exit the crankcase. The gases are then routed into the intake system so they can be re-burned in the engine. Fresh air enters the crankcase through a breather tube to facilitate this circulation and keep the air in the crankcase clean.

The PCV valve, like most working parts on a vehicle, will wear out over time. Usually it simply gets gummed up. Preventive maintenance, including routine oil changes at Muffler & Go in Fenton, will extend the life of the valve, but eventually it will have to be replaced. A sticking PCV valve won't allow gases to circulate properly, which can increase pressure in the crankcase. Over time, that pressure will lead to oil leaks.

Your vehicle manufacturer recommends that a PCV valve be replaced every 20,000 to 50,000 miles (32,000 to 80,000 kilometers), depending on the vehicle and Fenton driving conditions. It's an inexpensive repair but may not be included in the maintenance schedule in your owner's manual.  So if you're looking for auto advice about the PCV valve, you may have to ask our pros at Muffler & Go.

Taking care of our PCV valve protects the environment in MI and improves vehicle performance. It's just part of good vehicle care for Fenton drivers and a way all of us can do our part to improve the world we live in.

Muffler & Go
1478 N Leroy St
Fenton, MI 48430
(810) 629-1066
http://www.mufflerandgo.net

A "Mounting" Problem (Motor Mounts)

You know how heavy your engine and transmission are, so you can imagine how tough the parts that hold them onto your vehicle's sub-frame must be.  Not only must they support the weight, they also have to isolate vibrations and noise from the passenger cabin.  Pretty tall order, wouldn't you say?

The parts that face that task daily are called the motor mounts, or engine mounts.  They are usually made of rubber with steel brackets.  Others contain a liquid for vibration and sound isolation. 

Most vehicles have three or four motor mounts, and while rubber or hydraulic liquids do a good job of damping the vibrations from the engine, they also have their limitations.  The problem with rubber is that it gets old and brittle.  Plus, if there's an oil leak anywhere in your engine and oil gets on the rubber motor mounts, rubber will deteriorate even more quickly.  As for the liquid motor mounts, they can develop leaks and stop working. 

Here are signs a motor mount is going bad.  You may hear a loud clunking or banging sound under the hood.  That means the weight of the engine is shifting around enough to bang against other metal parts.  You may feel bad vibrations, and the engine may feel like it's moving around in a strange way.

When things get to that point, your vehicle can be damaged from that heavy engine knocking against things, and its time to replace one or more motor mounts.  Schedule a visit to your vehicle service facility. There, a technician will assess your motor mounts; if one bad one is found, it's not unusual that others are likely to fail soon and should be replaced before they do.

Because all vehicles are configured differently, some motor mounts are easily replaced.  But others can be much trickier, take a lot longer and therefore are more expensive to replace. 

It's important for your engine's health to make sure motor mounts are sound and solid.  You will maintain that quiet, vibration-free ride and could save your engine and transmission from major wear and tear.

Muffler & Go
1478 N Leroy St
Fenton, MI 48430
(810) 629-1066
http://www.mufflerandgo.net